​Since 1957, UNIST has been writing the book on non-friction.
They continually develop Micro-Fluidization systems so you can lower the cost and volume of lubrication in your cutting, forming and stamping operations. Their revolutionary lubrication systems avoid the need to flood fluid on machining and cutting hot spots. Much to the customers’ satisfaction, the system not only reduces how much lubricant bought, but also reduces the downstream costs of cleaning it up, treating and disposing of it. We recommend these systems for anyone looking to control their coolant usage and cost effectiveness.

Don’t forget your Misting Fluids!

Uni-MAX® Saw Lubrication System
​This is our top seller! Say goodbye to messy coolant floods!

Uni-MAX® Saw Lubrication System with a 3-Outlet BAT Nozzle improves life of band or circular blades
  • Extends blade life
  • Produces a continuous output of precisely metered lubricants. Variable-rate pulse generator allows for automatic, infinite repeat cycling of the metering pump from a single, dry filtered air source.
  • Adjusts output from 4-200 injection cycles per minute. Delivers 0.1 to 3.0 drops of lubricant per cycle. Standard 16-ounce reservoir holds more than 14,400 drops of lubricant.
  • Dispenses any highly refined lubricant including UNIST’s high-efficiency Coolube®.
  • Simultaneously lubricates the teeth on both sides of the blade. Applies a thin film of lubricant that prevents friction build up, maximizes saw productivity and blade life, reduces fluid consumption and produces near dry, easily recycled chips.
  • Lets operator easily control output by adjusting air, pulse per minute and liquid metering.
Click Here for Brochure
File Size: 2665 kb
File Type: pdf
Download File
Click Here for Brochure
File Size: 3483 kb
File Type: pdf
Download File
Uni-MAX® Coolubricator System

 Uni-MAX® Coolubricator System delivers precise and continuous lubrication!
  • Produces a continuous output of precisely metered lubricants. Variable-rate pulse generator allows for automatic, infinite repeat cycling of the metering pump from a single, dry filtered air source.
  • Adjusts output from 4-200 injection cycles per minute. Delivers 0.1 to 3.0 drops of lubricant per cycle. Standard 10-ounce reservoir holds more than 9000 drops of lubricant.
  • Dispenses a wide range of fluids (viscosity up to 20,000+ sus) including UNIST’s high-efficiency Coolube from its durable, 10-ounce (0.3 L) vented reservoir.
  • Combines lubricant and air in the patented co-axial nozzle tip. Keeps atomization and distribution of the liquid consistent regardless of the hose length. Nozzle is coupled with 5-foot co-axial hose and comes with a magnetic base for easy relocation and positioning at friction points.
  • Adjusts air and liquid output easily.
  • Offers choice of actuation valves: manual sleeve valve, electric solenoid or air pilot. This facilitates simple integration to your processes and equipment controls.
  • Creates a cleaner and safer work environment.
 Uni-MAX Coolubricator recommended for:
  • Metal cutting, machining and stamping
  • Plastic cutting and machining
  • Wood cutting and machining
  • In-die lubrication
  • Chain lubrication
Portable Uni-MAX® Coolubricator Jr.

Portable uni-MAX® Coolubricator Jr. lets you lubricate machines throughout your shop​
  • Moves from machine to machine without production delays. Hand-carry this versatile lubricator from one scheduled cutting or machining equipment to the next. A heavy-duty magnet lets you install it with minimal downtime.
  • Produces a continuous output of precisely metered lubricants. Air-driven, positive-displacement pumps precisely meter each drop of lubricant at .03 cc/stroke. The 100-million cycle pulse generator allows for automatic, infinite repeat cycling of the metering pump. This ensures that a continuous, external film of lubricant is applied to the tool-work interface.
  • Adjusts output from 4-200 injection cycles per minute with 0.1 to 3.0 drops of lubricant per cycle. A durable, vented 16-ounce reservoir holds more than 14,400 drops of lubricant.
  • Dispenses any highly refined lubricant including UNIST’s high-efficiency Coolube from its durable, 16-ounce (0.5 L) vented reservoir.
  • Combines lubricant and air in the patented co-axial nozzle tip. Keeps atomization and distribution of the liquid consistent regardless of the hose length. Plastic 12-inch nozzle is coupled with 5-foot co-axial hose. A heavy-duty magnetic base at the hose/nozzle connection makes it easier to relocate and position the nozzle at the friction points.
  • Lets operator easily control atomization of the spray by adjusting air, pulse per minute and liquid metering.
  • Installs fast and easy with manual on-off (sleeve).
  • This portable lubricator can lead to BIG lubricant savings and better quality products.
Uni-MAX Coolubricator Jr recommended for:
  • Drill presses
  • Lathes
  • Saws
  • Open milling machines
  • Boring mills
  • Works with metals, woods and plastics
Click Here for Brochure
File Size: 861 kb
File Type: pdf
Download File
Click Here for Brochure
File Size: 5989 kb
File Type: pdf
Download File
Uni-MAX® Serv-O-Spray Systems

Uni-MAX® Serv-O-Spray Systems for intermittent output
  • Operates with intermittent air signal. Add any amount of air to atomize the liquid lubricant. An air metering screw controls the flow of air out the nozzle. Lets you adjust spray density and distance. One shot of lube per cycle.
  • Adjusts output from manual to 200 injection cycles per minute. Delivers 0.1 to 3.0 drops of lubricant per cycle. Standard 10-ounce reservoir holds more than 9,000 drops of lubricant.
  • Dispenses any highly refined lubricant including UNIST’s high-efficiency Coolube.
  • Combines lubricant and air in the patented co-axial nozzle tip. Keeps atomization and distribution of the liquid consistent regardless of hose length. Nozzle is coupled with 5-foot co-axial hose and comes with a magnetic base for easy relocation and positioning at friction points.
  • Lets operator precisely direct spray. Spray output is at an angle approximately 11-18 degrees based on the amount of air introduced into the system. Operator controls area covered by increasing or decreasing the air and liquid controls.
  • Offers choice of actuation valves: none, solenoid or air pilot for electrical or pneumatic operation.
Uni-MAX Serv-O-Spray recommended for:
  • Supplemental and spot lubrication
  • Single or multiple spindle drills and taps
  • In-die lubrication
uni-MAX® Single Line System
uni-MAX® Single Line System for operations requiring a more compact, economical system
  • Modular, compact design offers an economical lubrication system.
  • Produces a continuous output of precisely metered lubricants. Variable-rate pulse generator allows for automatic, infinite repeat cycling of the metering pump from a single, dry filtered air source.
  • Output adjustable from 4-200 injection cycles per minute. Delivers 0.1 to 3.0 drops of lubricant per cycle. Standard 10-ounce reservoir more than 9,000 drops of lubricant.
  • Air and liquid lubricant combine in air chamber to create a lubricant spray dispersed through 1/8-inch OD, 10-foot nylon tube. This tube is positioned by a 1/8-inch OD semi-rigid copper nozzle that precisely directs the spray at the cutting tool or work piece. Comes with a magnetic base for easy relocation and positioning at friction points.
  • UNIST Variable Orifice Tip (VOT) provides proper lubricant velocity and consistency for continuous application.
  • Operator easily controls output by independently adjusting air and liquid delivery.
  • Choice of actuation valves: manual, solenoid or air pilot for manual, electrical or pneumatic operation. 
 uni-MAX Single Line recommended for:
  • Metal cutting, machining and stamping
  • Plastic cutting and machining
  • Wood cutting and machining
  • In-die lubrication
  • Chain lubrication
  • Use on metals, woods and plastics
Click Here for Brochure
File Size: 2518 kb
File Type: pdf
Download File
Portable uni-MIST System

Portable uni-MIST System prevents friction build-up in higher RPM tools and rapid stock feeders
  • Optimizes cooling effect of water-soluble lubricants with low volume/low pressure (LVLP) system. uni-MIST finely atomizes water-soluble lubricants with just enough air to quickly evaporate and optimize the cooling effect at the tool/workpiece interface.
  • Reduces fogging and overspray problems that occur with many siphon or suction-type mist systems.
  • Creates the exact atomized spray you need for your application. Coolant/lubricant moves to the nozzle tip under low pressure (15-30 psi). Operator precisely controls the mix of compressed air and liquid in the nozzle chamber.
  • Offers choice of manual or automatic operation. A manual control, on-off piston comes standard to precisely and constantly dispense lubricants and air.
  • Or add an optional solenoid or air pilot valve for automatic operation. The uni-MIST system will automatically operate or shut down with the tool’s normal operation. Valves control both air and liquid shut-off and operate instantaneously when a control signal is supplied. Both the solenoid or air pilot valve can control up to six, simultaneously in-use nozzles.
  •  Uni-MIST comes with a 12-inch, semi-rigid copper co-axial nozzle and 5-foot tube so you can position the spray on the tool/workpiece interface. Flexible nozzles are available in armored steel or flexible plastic .

We are not like the other guys, we KNOW Saw Cutting 

Hours

M-F: 8:00am - 4:30pm

Telephone

Ph L1: 909-941-6699
Ph L2: 909-941-9901

Email

sales@SCcuttingsolutions.com